Controlling Of Home Appliances Using Gsm Technology
This is a project work using GSM Technology to control home appliances.… Continue Reading
This is a project work using GSM Technology to control home appliances.… Continue Reading
Contents TITLE PAGE i CERTIFICATION AND APPROVAL ii DEDICATION iii ACKNOWLEDGEMENT iv ABSTRACT v TABLE OF CONTENTS vi LIST OF FIGURES viii CHAPTER ONE 1 INTRODUCTION 1 1.1: PROBLEM STATEMENT 1 1.2: THE AIM AND OBJECTIVE OF THE CLAP ON-CLAP OFF SWICHT 2 1.3: JUSTIFICATION OF THE RESEARCH 2 1.4: LITERATURE REVIEW 2 CHAPTER TWO 5 THEORY AND PICTORIAL… Continue Reading
The aim of this work is to characterize properties and microstructure of stainless steel used as a coating on welding of carbon steel sheets. Two carbon steel plates were set as the metal base and the stainless steel coating was applied on the weld bead. The applied process used was the submerged arc welding (SAW) and tests were carried… Continue Reading
This project shows the construction of a microcontroller based security door using Smart card. It is aimed towards programming the microcontroller to control the Hardware in sliding door. The system consists of a microcontroller 89S52 which Sends a signal to the multiplexers on insertion of the smart card in the card slot. The… Continue Reading
This project as the name implies is chosen, designed and constructed with the intention of transmitting information such as musicals news intertainments programs and soon. And all these that are written above are being transmitted to the atmosphere using an electromagnetic, signal, and this particular project design and construction is… Continue Reading
My project is to improve JIT store management system from manual to automated system. Which is used to avoid problem faced by store keeper when store material manually. Store is the place where many varieties of materials are kept for the purpose of work. So at a time of storage is hard to write in document all material listing by… Continue Reading
Electricity is fundamental and inevitable to our daily living as it lighting our environment, powers our homes, schools, hospitals, offices, businesses, and aid industrialization, It is a known phenomena that the economic growth of a nation rides on the wheel of electricity. While the telecommunication market in Nigeria has recorded… Continue Reading
A traffic light also known as a traffic signal, stop light and go light, robot or semaphore is a signally device positioned at four (cross) junction, pedestrian crossing or other locations in other to indicate when it is safe to drive or walk using a universal color code ( and in precise sequence for those that are color blind). Traffic… Continue Reading
Waste and residuals are undeniably part of the human society. The accumulation of these materials and the “throw away” philosophy results in many environmental and health issues and safety hazard problems prevent sustainable development in terms of resource recovery and recycling of waste materials. The carbon sources in the waste can… Continue Reading
In the world today, the use of power supply in electronics equipment and gadgets has increased and it is still increasing. These power supplies are not stable as required by these electronics. This arise the need for the power stabilization as to overcome this problem This project handles this problem very well. Some recommendations were… Continue Reading
INTRODUCTION As the world is developing the need for electronics in human endeavor is now taking a larger scope. With the invention of certain electronics gadgets in our societies today, certain activities become easily handled for example; in communication where the telephone plays a part. In places where safety are needed an alarm system will be… Continue Reading
This design implementation of this electronic sequential sign post display employs the use of some specialized components. This section of the project introduces the reader to the different section of the project and the components that makes them up. Emphasis are laid on describing the behaviour and operational system of the components… Continue Reading
The household lighting cost accounts for 10% of the electric bill, changing the light bulbs effectively can reduce the long term energy costs significantly. In Nigeria, where less than one percent of the population has access to 24 hours of interrupted power supply there is a need for a complementary, renewable source of light which provides… Continue Reading
The aim of this project is to shows the possibility of wireless power transfer through the design of a wireless charging pad. In this project write-up, the methodology and principle of operation is wireless power transfer through inductive couple, a feasible design is modelled accordingly. The inductive couple technique is used because it is the… Continue Reading
This project work was embarked on the construction and determination of the efficiency of 12 volts DC fan using two N3055 transistor, 1kΩ variable resistors, resistors, breadboard, veroboard, 12 volts DC battery and connectors at Science Laboratory Technological Department, Federal Polytechnic Offa, Nigeria. This is always required to… Continue Reading
In our present society, wireless communication has become most prevalent and mobile units (hand held devices /GSM/ Computers) are one of the most common equipments for conveying messages wirelessly. Owing to the fact that most youths in our society today on the average make use of at least one wireless device that communicate with other… Continue Reading
A smoke detector is a device that senses smoke typically as an indicator of fire or non- smoking zone. In order to ensure human safety and safeguard property against fire in both domestic and commercial settings, different solutions for smoke detection have been developed, a comprehensive literature was carried out on smoke detector,… Continue Reading
The Orsat Gas Analyzer was constructed at the project development institute (PRODA), Enugu. The operation involved the laboratory glass blowing which entails the heating of a glass tube. The heating •continues until the glass tube reaches its plastic state. The shape of the tube is changed or the required shape blown by pulling, bending… Continue Reading
The motive of this project is to construct equipment for deodorizing kerosene, hence the smell of kerosene is totally eradicated. The equipment was constructed with flat sheet plates of a desired standard, the dimension and the truncated parts were coupled and welded in order to fasten the parts together. The material was selected to… Continue Reading
This project involves the development of a console that allows multiple inputs (3 inputs) and a single output to a screen through the use of software. The micro controller which serves as the ‘heart’ of the hardware was encoded using C programming language. These lines of code enable the micro controller to switch to the selected… Continue Reading
This work is based on automatic changeover switch. If there is failure in main power supply it will automatically change to auxiliary power supply such as generator. This project is based on electromechanical changeover with the use of magnetic contractors, relay,and circuit breaker.… Continue Reading
INTRODUCTION This project presents the design and construction of a computer based program used to control office appliance. It is based on a Graphic user interface (GUI) programming language (Visual Basic 6.0), Parallel Port Interactive Mode, Opto-Coupler Isolation of the computer from the appliance to prevent damage to the system should a fault… Continue Reading
This system “” comprises of many modules which are: The Sensor/Input Unit, Microcontroller Unit and the Output Interface. The sensor detects when the hand approaches the nozzle. Once the approaching hand is detected, the hand dryer produces a very hot to dry the hand as well as… Continue Reading
This design is aimed at providing a system that has the capability of recharging batteries after use. The design is to incorporate an auto charging cut off circuit that operates when the battery is fully charged to avoid damaging the device and also a low voltage circuit which prevents the system from damage should in case the battery… Continue Reading
The world today is moving ahead at a very fast pace. Some of the very common examples of fast moving objects are aeroplanes, high speed cars and many more. In our everyday life we come across many fast moving vehicles and so it is very important to measure the speed of these vehicles.This is an era of automation where it is broadly… Continue Reading