This project involves the development of a console that allows multiple inputs (3 inputs) and a single output to a screen through the use of software. The micro controller which serves as the ‘heart’ of the hardware was encoded using C programming language. These lines of code enable the micro controller to switch to the… Continue Reading
Project The main aim of this system is to detect object that will be ahead of ultrasonic transducer. This application is very useful in areas like monitoring and also very useful in wild life photography. There are two main parts of the ultrasonic detector. First one is emitter that produces a 40kHz sound wave. Second… Continue Reading
This project report describes the design and construction of an electronic door lock which uses a microcontroller as the main control unit. The project’s objective was to interface this microcontroller with an LCD, keypad and a DC motor. However, programming the PIC chip to perform a task like identifying an authorised user is also… Continue Reading
TABLE OF CONTENT: CHAPTER ONE INTRODUCTION 1.1 OBJECTIVE OF PROJECT 1.2 JUSTIFICATION OF PROJECT 1.3 SCOPE OF DIAGRAMS IN PROJECT 1.4 BLOCK DIAGRAM OF PROJECT 1.5 PROJECT REPORT ORGANIZATION CHAPTER TWO LITERATURE REVIEW 2.1 REVIEW OF REMOTE CONTROL SYSTEMS 2.2 DESCRIPTION OF PROJECT 2.3 USE OF… Continue Reading
The need for a remote control system that can control domestic appliances and various lighting points and sockets has often been a concern for uses at times uses find it inconvenient and time they are leaving the house for work it has also often led to damage of appliances due to the fact that an appliances was not timed off before… Continue Reading
ABSTRACT The design and construction of the House Bell with indicating light system was creative embarked on for the production of a better alarm signals. Meanwhile different measures and steps such as using electric bell, electric bulb, light emitting diode, 1 mm2 their cable, B Amps plug, lamp holder was used to achieve the objective. All the… Continue Reading
The very fundamental reasons behind this project assignment is to expose student to the very important aspect of private and independent research work not only theories but also subsequent translation of the theoretical research work into a particular function system. The project construction of automatic fence light controller has been… Continue Reading
TABLE OF CONTENTS Title Page Certification Page Acknowledgements Dedication CHAPTER ONE:INTRODUCTION 1.1Definition of Term CHAPTER TWO:TRANSFORMER FUNDAMENTALS CHAPTER THREE:DESCRIPTION OF COMPONENTS 3.1Resistors 3.2Capacitors 3.2.1Types of Capacitor 3.3Semi-Conductor Diode 3.4Transistors 3.4.1Bipolar Transistor 3.5Field Effect… Continue Reading
This is a technical project write-up design and construction were carried out by me with deep intensive and extensive research work. I all give credit to the authors of the textbooks whose I referred to in the cause of writing this project and its subsequent design and construction. In this project, I shed light on the basic principle… Continue Reading
Engineering being the mother every technology cannot be neglected. Without practical application in the field of engineering. The student and their tutors are impotent. The lucrative nature of engineering depends on the technical know-how of the engineer. The purpose of practical project to students is to help them acquire practical… Continue Reading
The uninterrupted power supply (UPS) is design to help in the offices, workshops and house hold appliances, due to the unstable power supply being supplied by (NEPA) presently known as Power Holding Company of Nigeria (PHCN) usually supply to us. With the help of the UPS we don't need to depend much on PHCN it is stress free because it… Continue Reading
This project the design an construction of fire alarm was carried out with deep intensive and extensive research work my aim and objective in the price of work is to produce a standard device or electronics that will inform the security about a fire outbreak in the company or house for a quick reaction/action. In this project I shade… Continue Reading
ABSTRACT This project intended to simplify the description and working principle of FM wireless microphone, which works on a fixed frequency modulation (FM) band. TABLE OF CONTENTS Approval Sheet Title Page Dedication Acknowledgement Abstract CHAPTER ONE 1.0INTRODUCTION 1.1Aim and Objective of Investigation CHAPTER TWO … Continue Reading
Amplifiers, which are devices that increase the gain of an audio signal, dominate modern audio technologies. In this project, we designed and built an audio amplifier from scratch in order to demonstrate that such a key device can be constructed using basic electrical engineering principles. After performing major circuit calculations by hand, we… Continue Reading
The project work is on the design and construction of automatic two lane traffic light control. This system is based on digital electronics. It employs an astable multivibrator which is the clock generator that sends the clock into a time sequencing generator using a decade counter with ten (10) decodes output that has it’s… Continue Reading
This project is titled the design and construction of a DC to AC inverter system. It is designed to meet up with the power demand in the offices and in homes in the absence of power supply from the national supply authority, NEPA. In order words the device / item serves as a substitute for NEPA which almost monopolises the power supply to… Continue Reading
PREFACE The aim of this project is to construct power amplifier. The system is expected to amplify. The major components in the circuit is the integrated circuit (IC JRE with some circuit elements for the normal operation of the circuit. So as to amplifier an output, the general construction dealt with in the chapters. The levels of… Continue Reading
The design of this 30 volt Audio Amplifier with volume, table and bass control which was done wit ht he combination of five (5) different circuit which are interconnected during or after construction. This amplifier operates with an option of a left and right channel. The combination of these circuit include this main amplifier circuit… Continue Reading
This project present a practical demonstration of how to carryout the wiring of a two bedroom bungalow, using PVC conduit system. In recent times surface wiring is gradually giving way to conduit wiring where much of the cable are concealed. PVC pipes are used because of it cost friendliness, compared to metal conduit. In carryout this… Continue Reading
The project work on construction of loud speaker involves some critical research and study concerned electromagnetic induction effect in transducers like loud speaker and its associated parameter required to chose a very good one this parameters are the power rating of loud speaker and the coil. The sizes were also put into… Continue Reading
As technological advancement has been on the increase in our society many have fallen in love with technology and world want to have a feel in virtually to every thing they do. A design has been made in combination of electrical and electronics to change over from one power sources to the other automatically and trip off generation… Continue Reading
As the zeal for change over on public power supply and stand- by generator increases; Engineers have researched deeply into the different ways and methods of achieving power changeover both manual and automatic types. It may no be considered as serious issue in some places where supply is up to 90% constant or where intermittent outage… Continue Reading
This project write up of a step – down transformer from 220v to 24v:12v, this is to expose what a transformer is all about and its important and uses. The aim of the project, step-down transformer is to show Electrical and Electronics Engineering, could step-down the voltage from 220v to 24:12v, and fro this project write up.… Continue Reading
This project work is on the construction of an F.M transmitter this system consists of four discrete modules namely the audio frequency (AF) amplifier (class A) the modulator the master oscillator and the radio frequency (RF) amplifier (ClassC) these formed the conventional events for building FM transmitter here the signal (from the… Continue Reading
The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery charger. However the procedure fro developed… Continue Reading