INTRODUCTION The separation operation of drying converts a solid, semi-solid or liquid feedstock into a solid product by evaporation of the liquid into a vapor phase via application of heat. In the special case of freeze drying, which takes place below the triple point of the liquid being removed, drying occurs by sublimation of the solid phase… Continue Reading
Note:This work contains only the schematic diagram/design of a biogas plant Biogas typically refers to a mixture of gases produced by the breakdown of organic matter in the absence of oxygen. Biogas can be produced from regionally available raw materials such as recycled waste. It is a renewable energy source and in many cases exerts a very small… Continue Reading
The general approach to any design of a process plant involve an advanced network of chemical engineering process. Absorber is a process plant or equipment that are used in the purification of gas or separation of unwanted gas from the mixture when it comes in contact with the liquid. In this models mass transfer reaction and equilibrium… Continue Reading
This report aimed at determining the presence and removal of mercaptan sulphur in kerosene using colour indicator method. It is known that impurities such as free sulphur, sulphur dioxide, marketers, finding materials etc. are found in petroleum products. Consequently, absorbents like molecular sieve, calcium oxide and even activated… Continue Reading
This project was carried out to ascertain whether the local palm oil met the required standard. The analytical test carried out include the free fatty acid test the acid value, iodine value moisture, content, saponfication value, peroxide value, specific gravity, colour and viscosity. The specific gravity of the oil sample was determined… Continue Reading
This project “production of plane mirror using local raw material” is meant to study the possibility of producing plane mirror using sand rich in silica as its major local raw material. Plane mirror is produced by casting one side of a sheet glass. Presently in Nigeria, sheet glass is not used easily produce and as such, the local raw… Continue Reading
A paint mixer is defined as a pattern constructed for the production (mixing) of paint manually. The method of fabrication of the paint mixer involved a preliminary computation of the dimensions of the standard mixer in relation to the dimension of the reacting vessel in which they will be used in marking out, cutting out to sizes,… Continue Reading
The spread of pollutant in an area is partly a function of wood burning in local kitchens by the population of the area. This pollution generated through combustion of wood fuels presents difficult environmental challenges to societies as it could degrade the environment and affect human health and quality of life. Wood burning emissions are… Continue Reading
The interest in using Jatropha curcas L. (JCL) as a feedstock for the production of bio-diesel is rapidly growing. The properties of the crop and its oil have persuaded investors and policy makers to consider JCL as a substitute for fossil fuels to reduce greenhouse gas emissions. In this report, we gave an overview of the currently… Continue Reading
Bioremediation is an important technology for the restoration of oil polluted environments by indigenous or selected microorganisms. In general, the rate of biodegradation depends on the number and types of micro-organism, the nature and chemical structure of pollutants to be degraded and the environmental conditions. In this study, the… Continue Reading
This project envisages the establishment of a plant for the production of high fructose corn syrup with a capacity of 6,000 tons per annum. The country`s requirement of corn syrup is met through import. The present (2013) demand for syrup is estimated at 5,000 tons. The demand for the product is projected to reach 8,858 tones and 14,266 tons by… Continue Reading
Team Oil from [the] Soil is comprised of a group of senior chemical engineers at Calvin College who are proposing an alternative method to producing biodiesel. This alternative entails converting the oil found in seeds from the Jatropha Curcas plant into biodiesel. Team Oil from [the] Soil plans to design and optimize a full scale plant that… Continue Reading
ABSRACT The fabrication of a set of sieves and shaker was carried out in paliton workshop, Enugu. After a thorough analysis on the suitable materials to be used in fabrication, galvanized steel was chosen due to its advantages over materials of fabrication. The fabrication was carried out in order to analyze the sizes of particles. The component… Continue Reading
This is an abstract on the construction of a packed distillation column. A packed distillation column is used in the separating process distillation that is the separation of two miscible liquids. It was constructed by marking out the dimension of the column, condenser, pot, using steel rule scriber, oxyacetylene flame was used for… Continue Reading
The sets of seizes with shocker which was fabricated and assembled in the chemical engineering pilot plant was aimed at providing the students with a machine that will aid them in practical involving the separation of solid particles. Besides this, it was also fabricated sizes or diameter of the solid particles of a substance by allowing… Continue Reading
This project was carried out using acid activated coal from Enugu coal and the production of ve4getablew oil was monitored using spectrophotometer to measure the absorbance. It was also perform to check the suitability of activated Enugu coal as a bleaching agent for palm oil. The Enugu coal samples were collected, size reduced,… Continue Reading
This study was carried out principally for the formulation of artist paint using available raw materials. Paint simplified is a material which may be applied to surfaces in relatively thin layers and which changes to a solid and may occur by evaporation of solvents, by chemical reaction or by combination of the two. Artist paint is the… Continue Reading
The fresh cassava were sources from Idodo in Nkanu Local Government of Enugu state. The weight of the cassava tuber were taken to be 31.50kg. After peeling and washing, it was divided into two equal parts which was 21.13kg for production of sample A and sample B respectively (edible and textile starch) which weighed 13.1kg. During this… Continue Reading
The advent of sachet and bottled water has increasingly filled the gap in household water security. This research work was carried out to assess the quality of bottled and sachet water sold in Bauchi metropolis. Thirty (30) water brands consisting of twenty (20) sachet water brands and ten (10) bottled water brands were assessed for their… Continue Reading
This project contains details of Coal fired circulating fluidize boiler.The motivation of our project was to develop a method which is energy economical i.e. uses less energy owing to increasing energy issues. Process description, mass balance, energy balance, equipment design, and cost estimation of circulating fluidized bed boiler for combustion… Continue Reading
ABSTRACT Biomass is organic materials that are made from plants and animals. Biomass stored alot of energy from the sun. Biomass is renewable sources of energy which can grow more such as trees and crops,… Continue Reading
It's a journal that explains the design of a shea butter plant.… Continue Reading
A study on the effects of post- harvest variables on the yield and quality of Shea butter wascarried out. The Shea nuts acquired from villages were divided into five batches with avillage/uncontrolled sample. Each batch was boiled at different time ranges (0, 15, 30, 45 and60) minutes. Each batch was dried through an oven drying method.… Continue Reading
Crude oil viscosity is an important parameter which is considered in both porous media and in pipeline channels. Estimating oil viscosity at various operating conditions of pressure and temperature is of great value to petroleum engineers. In petroleum and reservoir engineering, we are often faced with the analysis of processes which involve… Continue Reading
Kenaf reinforced polyethylene composites for ballistic protection was produced in this work. The samples of alkaline treated and silane-coupled non-woven matted kenaf fibers were cut to the required dimensions and oriented vertically and horizontally in combinations with a virgin high density polyethylene (VHDPE). The composite panels were… Continue Reading