Focuses on the maximum volume of waste generated in a particular month in a particular area and uses a heuristic model for it's analysis. Research Problem A proper, efficient, reliable and hygienic waste handling and disposal technique tells more of our maintenance culture but the capacity and ability to efficiently manage the waste becomes… Continue Reading
Indirect combustion noise had not been attracting research in the past, but recent indication seems to prove that it could be a threat in the future if not addressed. Means of reducing this type of noise to a low decibel value was also included. Noise is due to the ingestion of distorted atmospheric turbulence, as the two set of blades… Continue Reading
This project covers the design and construction of a power generating windmill. The designs was carried out based on long-term available wind data of bida at 10m above the ground level. The average wind speed for Bida is 5.24m/s and rated turbine wind speed is 6.29m/s. The design of each components of the system were carefully constructed in a… Continue Reading
Analysis of Longitudinal Aerodynamic Characteristics of an Aircraft Model with and Without Winglet Altab Hossain a *, Prithvi Raj Arora b , Ataur Rahman c , Abdul Aziz Jaafar b , A.K.M. Parvez Iqbal a a Department of Mechanical Engineering, University Industry Selangor, Jln Timur Tambahan, 45600 Batang Berjuntai, Selangor Darul Ehsan,… Continue Reading
This project covers a study of the effect of seawater corrosion on 0.34% and 0.36% carbon steel compositions. Two (2) specimens (steel rods) of length 150mm (each) for both steel compositions were obtained. Out of each was gotten four (4) specimens of 10mm length, 10mm diameter and two (2) specimens of 50mm length, 10mm diameter. This… Continue Reading
The major components of a gas turbine are compressor, combustors, turbine and generator. It operates by continuous drawing in fresh air into the compressor. The Air is then compressed to a high pressure in the compressor and discharge into the combustion. Here the air is missed with gas and burns continuous once ignited to increase its energy… Continue Reading
This project illustrates the use of an exergetic approach to analyze the performance of a vapor compression refrigeration system using a refrigerant solution of a nanoparticle (TiO2), mineral oil, and R410a (base refrigerant). Exergy investigation is a thermodynamics strategy which allows for the assessment and improvement of a… Continue Reading
The rate at which energy is lost by human activities is enormous. There is need to work on how to generate more energy and minimize the usage of the generated energy. In an internal combustion engine, there is need to focus on gaining energy usage by using generated heat during combustion process. To reduce the energy usage, emission rate… Continue Reading
Limited or poor food separation techniques into fine particles for further processing cause post-harvest losses of food crops and initiates the problem of food and nutritional insecurity in Nigeria. In order to solve this problem, food crops need to be processed into a lasting and nutritious consumable form through the use of mechanization.… Continue Reading
The fabrication of the solar dryer was successful and test were carried out for various performance comparisons such as No-load and Load performance of the dryer and direct sun drying comparison and noticeable differences was noticed in the final moisture content such that the maximum temperature recorded in the drying chamber and solar… Continue Reading
When comparing with other manufacturing technologies, the extrusion technology always stands out as it is known to be highly efficient in terms of producing products of superior quality with the least possible amount of wastage. With the ever-increasing cost of materials, energy and the competition in the market, it becomes almost… Continue Reading
This work investigated the variation of top loss heat transfer coefficient with the emittance of the absorber plate, the collector tilt angle and air gap spacing between the absorber plate and the cover plate. The effects of the emittance of the absorber plate, the collector tilt angle and air gap spacing between the plate and the cover… Continue Reading
CHAPTER ONE: INTRODUCTION 1 Background of the Study 1 Statement of the Problem 6 Objectives of the Study 7 Justification for the Study 8 Scope and Limitations of the Work 9 Scope 9 Limitations 9 CHAPTER TWO: LITERATURE REVIEW 10 2.1 Small Hydropower Systems 10 2.1.1 Types of Hydroelectricity Generation 13 2.1.1.1 Conventional Hydroelectricity 13… Continue Reading
Working adults and university students find it difficult to complete their laundry in a day because of the unpredictable weather conditions in the tropics of West Africa. There are existing drying machines, but these machines are either not smart or they are hard to install and maintain and they cause easy damage to the clothes. In… Continue Reading
Gari is a very important staple food made from cassava and is eaten in many parts of Africa. Gari has a granular nature and may contain different sizes of grains ranging from as small as 1 mm to as large as 6 mm. Depending on where and how gari is going to be eaten, specific particle sizes are desirable. The market value of gari is… Continue Reading
As the world keeps evolving, the demand for electricity increases. The growing energy consumption leads to higher cost that many people, especially in Ghanaian rural areas, cannot afford. Thus, considering this, this paper focuses on designing a Stirling engine to pump water in homes. In order to contribute to the use of renewable energy… Continue Reading
An analysis report compiled by the OSHA lists eighty-eight (88) window cleaning accidents over the past 15 years of which sixty-two (62) resulted in fatalities [1]. Despite these statistics and the potential for injuries and deaths, the industry considers these numbers to be artificially low. Window cleaning is still not effectively… Continue Reading
All-Terrain vehicle as the name implies refers to a car that has been designed to handle a more extensive variety of terrains than most other cars. ATVs are used for several purposes which include recreational purposes and others ranging from military to jungle safaris and desert rides. ATVs are rated highly based on their ability to… Continue Reading
This project paper explains the design and fabrication of an inflatable wing using a flexible, low cost and easily accessible PVC material. In recent times, several researchers have explored the building of inflatable structures using expensive and high strength materials like Mylar and Kevlar. However, this project scope was… Continue Reading
Green roofing is a relatively new approach toward constructing environmentally friendly and sustainable roofing structures. Not only are these structures environmentally friendly, but they can be manipulated for the purposes of energy harvesting, thermal insulation or cooling while saving cost in the long run. Much like the green roof… Continue Reading
A Wind tunnel is a mechanical assembly used to analyze the behavior of air flow and the effects they have over objects. Using a wind tunnel, one can control the stream conditions which influence forces on the test object. Through the calculations of the forces on the model, one can anticipate the forces on the full-scale test object. In… Continue Reading
In this project the design of an automatic ground vehicle for use in warehouses is explained. Ecommerce has been growing rapidly across the globe because of the spread of the internet and due to the introduction and acceptance of secure digital payment systems. Volumes of products handled by online stores has been increasing exponentially… Continue Reading
Synthetic biology is the engineering of biology; it is the evaluation and design of biological systems in a rational and systematic manner. It blurs the lines between various science and engineering disciplines due its numerous applications, with one of the most significant being the use of biosensors in environmental remediation.… Continue Reading
The objectives a welding flux is expected to achieve are many and often mutually incompatible.… Continue Reading
Industrial accidents are on the rise. This fact is even more prevalent in developing countries where the countries lack the safety standards required to ensure workplace safety in the pursuit of economic development. As land in prime locations becomes increasingly scarce, there is an argument for building skyscrapers. But this just… Continue Reading